Resonant slots are widely used for conventional slotted waveguide array. Reflection from each slot causes a standing wave in the waveguide and beam tilting technique is essential to suppress the reflection at the antenna input port. But the slot reflection narrows the overall frequency bandwidth and the design taking it into account is complicated. This paper proposes a reflection cancelling slot pair as an array element, which consists of two slots spaced by 1/4λg. Round trip path-length difference between them is 1/2λg and reflection waves from a pair disappear and traveling-wave excitation in the waveguide is realized. The full wave analysis reveals that mutual coupling between paired slots is large and seriously reduces the radiation from a pair. Offset arrangement of slots in a pair is recommended to decrease the mutual coupling and to realize strong coupling. In practical array design, the mutual couplings from other pairs were simulated by imposing periodic boundary conditions above the aperture. To clarify the advantages of the slot pair over a conventional resonant slot, the predicted characteristics are compared. Reflection characteristics of the array using the slot pair is excellent and a boresite beam array can be realized. In addition, a slot pair can realize stronger coupling than the conventional resonant slot, while the bandwidth of the former in terms of the aperture field phase illumination is narrower than that of the latter. These suggests that the slot pair array is much more suitable for a small array than conventional one. Finally, the predicted characteristics are confirmed by experiments.

Locality in high frequency diffraction is embodied in the Method of Moments (MoM) in view of the method of stationary phase. Local-domain basis functions accompanied with the phase detour, which are not entire domain but are much larger than the segment length in the usual MoM, are newly introduced to enhance the cancellation of mutual coupling over the local-domain; the off-diagonal elements in resultant reaction matrix evanesce rapidly. The Fresnel zone threshold is proposed for simple and effective truncation of the matrix into the sparse band matrix. Numerical examples for the 2-D strip and the 2-D corner reflector demonstrate the feasibility as well as difficulties of the concept; the way mitigating computational load of the MoM in high frequency problems is suggested.

This paper presents the design of low sidelobe single-layer slotted waveguide arrays. The Taylor distribution with -25 dB sidelobe level is synthesized in two orthogonal directions in the aperture. The multiple-way power divider consisting of a cascade of novel π-junctions is introduced; each π-junction, two-way power divider, is so designed as to accept unequal power dividing by adopting an offset window. The smooth Taylor distribution is realized at the output of the multiple-way power divider, which was originally developed only for uniform distribution. A model antenna for Taylor distribution is tested at 76 GHz. The measured sidelobe level is below -24 dB in both E- and H-plane. The highest gain is 34.5 dBi with 50% efficiency which is only 15% lower than that for uniform aperture illumination.

A Radial Line Slot Antenna (RLSA) is a planar antenna for DBS reception. It is a kind of slotted waveguide arrays. The conductor loss is so small that high efficiency is expected irrespective of the aperture diameter. On the other hand, since a RLSA utilizes the traveling waves, the frequency bandwidth is limited by the long line effect, particularly for a larger antenna. A new Wide-Band RLSA (WB-RLSA) is proposed which halves the waveguide length and widens the frequency bandwidth. This paper presents the design and experimental results of a model antenna. A gain of 33.7dBi is measured at the edge of 800MHz bandwidth and its high potential is demonstrated.

Excitation amplitude and phase coefficients of array elements are designed for the use of a primary feed reflector antenna with the intension of improving its beam scanning characteristics. Special attention is paid for beam isolation between two adjacent beams in an area coverage beam arrangement. After several method are compared, it is pointed out that coefficients determined in terms of aperture distribution are effective for compensating gain reduction in widely scanned angle, while they can not control beam isolation. Beam isolation, on the other hand, is effectively improved by designing array coefficients so as to arrange null points of the far field pattern on a circle with its beam direction centered. In this method, number of null points and radius of the circle are determined to get higher beam isolation. Number of null points may be set greater than that of elements, provided null points in the sense of a least mean square are also admissible. A simple parabola with offset angle of 45, fed by 9-horn array thus designed, can scan its beam beyond 10 halfpower beam width, keeping no less than 27 dB isolation between beams with spacing of about 2.0 halfpower beam width apart.

Physical optics (PO) have been extensively used in radiation pattern analysis of offset parabola. Physical Theory of Diffraction (PTD) proposed later has better accuracy. This paper presents an analytical/numerical comparative study of these methods to demonstrate the limitations of PO. PO envelope errors in co-polar patterns are expressed as functions of antenna parameters. Serious PO errors in cross polarization prediction are pointed out for antennas with cross-polar suppressing feeds polarized in the plane of asymmetry.

A 42×42-way one-body 2-D beam-switching Butler matrix with waveguide short-slot 2-plane couplers is designed and fabricated in the 22GHz band. The one-body configuration using the commutativity and the overlapping of units allows reducing the size and loss in comparison with a cascade of matrices beam-switching for the horizontal and the vertical planes. It is achieved by replacing 2×2-way 1-plane couplers in the conventional block configuration for a Butler matrix with 22×22-way 2-plane couplers. The measured bandwidth is approximately 2% restricted by the frequency characteristics of the 2-plane couplers. In the radiation from the aperture array antenna of the 42 output ports, the 3.9dB-down coverage of 3-D solid angle by the sixteen beams is around 1.72 steradian which is same as 27.4% of hemisphere at the design frequency for the aperture spacing of 0.73×0.73 wavelength.

This paper studies the performance of the quantitative RF power variation in Radio-over-Fiber beam forming system utilizing a phased array-antenna integrating photo-diodes in downlink network for next generation millimeter wave band radio access. Firstly, we described details of fabrication of an integrated photonic array-antenna (IPA), where a 60GHz patch antenna 4×2 array and high-speed photo-diodes were integrated into a substrate. We evaluated RF transmission efficiency as an IPA system for Radio-over-Fiber (RoF)-based mobile front hall architecture with remote antenna beam forming capability. We clarified the characteristics of discrete and integrated devices such as an intensity modulator (IM), an optical fiber and the IPA and calculated RF power radiated from the IPA taking account of the measured data of the devices. Based on the experimental results on RF tone signal transmission by utilizing the IPA, attainable transmission distance of wireless communication by improvement and optimization of the used devices was discussed. We deduced that the antenna could output sufficient power when we consider that the cell size of the future mobile communication systems would be around 100 meters or smaller.

Excellent characteristics of a single-layered radial line slot antenna composed of a copper clad laminates are reported. The use of a thick substrate contributes to reduction of conductor loss. The efficiency of 71% and the gain of 33.2dBi is realized for a 44cmφ prototype antenna.

In the design of a large slotted waveguide array, evaluation of mutual couplings between the slots is time consuming. This paper proposes an effective approximation analysis of the external mutual couplings using periodic boundary condition. Simple design procedure is verified for two-dimensional slot array.

An element consist of a slot and a post is designed for canceling the reflection in a rectangular waveguide by the method of moments. For reducing the computation time in practical design of the element with a wide range of coupling strength for an array, only the axial uniform currents on the post surface are considered. This approximation is valid when the post for reflection-canceling is far enough from the slot. The post location is determined by this simple analysis for both transverse and longitudinal slots with typical coupling strength. Measured results using 4 GHz-band standard waveguides reveal that the assumption of uniform line currents on the post surface is acceptable. The design is further extended to demonstrate its applicability to a practical array design by considering a wide range of coupling strength.

Physical optics (PO) is an approximation method for high-frequency scattering and diffraction problems. But PO fields are inaccurate in the shadow region where the source is screened by the scatterer. It has been difficult to extract the mechanism of this error because PO includes numerical integration. In 2-D problems, PO fields are analytically and accurately expressed in terms of PO equivalent edge currents (PO-EECs) which represent the leading contributions of PO original integration. Comparison of PO in this form and geometrical theory of diffraction (GTD) which gives accurate fields in the shadow region, clarifies the cause of PO errors. For a scatterer with a corner, PO errors are mainly due to the rays emanating from the invisible edges. For a curved surface scatterer, the contributions penetrating the scatterer are small and main PO errors generally consist in PO-EECs itself.

This paper presents designs and performances of 76 GHz band alternating-phase fed single-layer slotted waveguide arrays. Two kinds of design, that is, uniform aperture illumination for maximum gain and Taylor distribution for sidelobe suppression of -25 dB, are conducted. High gain and high efficiency performance of 34.8 dBi with 57% is achieved for the former, while satisfactory sidelobe suppression of -20 dB in the H-plane and -23 dB in the E-plane with high efficiency is confirmed for the latter. The simple structure dispensing with electrical contact between the slotted plate and the groove feed structure is the key advantage of alternating-phase fed arrays and the slotted plate is just tacked on the feed structure with screws at the periphery. High gain and high efficiency performances predicted theoretically as well as design flexibility of the alternating-phase fed array are demonstrated in the millimeter wave frequency.

A lightweight and high gain planar antenna for space use is realized with radial waveguide slotted array and honeycomb structure with the weight of 1.16 kg and the diameter of 920.5 mm. The slot coupling is analyzed by method of moments considering the hybrid mode in the multi-layer waveguide structure. The propagation constant of the honeycomb structure is measured and the low-loss property is obtained at the frequency range of 8 GHz. The fabricated RLSA is measured and the reflection is around -10 dB in 8 GHz band. The measured aperture fields agree with the calculation in the radial direction. In the azimuthal direction, on the other hand, the fields show ripples of 6 dB and 60 degree. The gain of 35.9 dBi with the efficiency of 58.7% is obtained at 8.6 GHz.

A 16×16-element corporate-feed waveguide slot array antenna in the 60-GHz band is designed to achieve broadband reflection and high antenna efficiency. The sub-arrays consisting of 2×2-elements are designed to improve the reflection bandwidth by implementing lower Q and triple resonance. The designed antenna is fabricated by diffusion bonding of thin copper plates. A wide reflection bandwidth with VSWR less than 2.0 is obtained over 21.5%, 13.2GHz (54.7-67.8GHz). The measured gain is 32.6dBi and the corresponding antenna efficiency is 76.5%. The broad bandwidth of more than 31.5-dBi gain is realized over 19.2%, 11.9GHz (56.1-68.0GHz). The gain in bandwidth covers the whole of the license-free 60-GHz band (57-66GHz).

A numerical design of a coaxial-to-radial line adaptor is presented for the use as a feed in a radial line slot antenna. To realize stable performances in mass production, the reflection from a probe type adaptor in which only the outer conductor of a coaxial line is in contact with the waveguide, is analyzed and suppressed. The tolerance for the change and the errors in the height of the waveguide as well as the bandwidth is highlighted; the advantages of the conical probe over the conventional shorting post and the coax-gap adaptor are emphasized.

As a promising lamination-loss-free fabrication technique, diffusion bonding of etched thin metal plates is used to realize double-layer waveguide slot antennas. Alternating-phase feed is adopted in this paper to reduce the number of laminated plates to simplify fabrication as well as to reduce cost. A 20 × 20-element double-layer waveguide slot antenna with a bottom partially-corporate feed circuit is designed for 39GHz band operation as an example. The adjacent radiating waveguides as well as the 2 × 2 sub-arrays fed in an alternating-phase manner eliminate the need for complete electrical contact in the top layer. However, the feed circuit in the bottom layer has to be completely diffusion-bonded. These two layers are simply assembled by screws. An antenna laminated by only diffusion bonding is also fabricated and evaluated for comparison. The comparison proved that the simply fabricated antenna is comparable in performance to the fully diffusion-bonded one.

A simple approximation method to calculate scattering from a grid with straight strips of finite size (the equivalent grid method) was proposed by the authors. This method can deal with arbitrarily polarized incidence with arbitrary plane of incidence. In this letter, the applicability of this analysis to the scattering from a grid with curved strips is demonstrated by experiments.

Electromagnetic scattering at high-frequencies is computationally heavy. Radar cross section (RCS) of electrically large concave and convex objects are solved by using the hybrid method. For convex and concave surfaces, Modified-Vector Physical Optics (MPO) with enhanced accuracy and Iterative Physical Optics (IPO) taking multiple-reflections into account, are selectively and independently applied for convex and concave parts of the scatterer. The accuracy of RCS by this hybrid method is tested with the MoM based simulator Wipl-D as the reference. The RCS from relatively small scatterers with the dimension of the order of a few wavelengths can be successfully predicted.